DVC DIN RAIL KIT

Voltage Transducer DVC 1000-UI UP N = 1000 V For the electronic measurement of voltage: DC, AC (UP ≥ 0 V), pulsed..., with galvanic separation between the primary and the secondary circuit. Features ● Unipolar and insulated measurement from 0 to 1000 V Standards ● EN 50155: 2017 ● 4-20 mA instantaneous output (unipolar power supply) ● EN 50121-3-2: 2016 ● Panel and DIN rail mounting ● IEC 62497-1: 2010 ● Push-in connections ● IEC 61000-6-2: 2016 ● Built-in device ● IEC 61000-6-4: 2016 ● Ingress protection rating IP 20. ● IEC 61800-3: 2005 Advantages ● IEC 61010-1: 2010 ● IEC 61800-5-1: 2007 ● Low consumption and low losses ● IEC 62109-1: 2010 ● Compact design ● Very low sensitivity to common mode voltage variations ● UL 508: 2018. ● Excellent accuracy (offset, sensitivity, linearity) Application Domain ● Fast delay time ● Industrial or Railway (fixed installations and onboard). ● Low temperature drift ● High immunity to external interferences. Applications ● AC variable speed and servo motor drives ● Static converters for DC motor drives ● Battery supplied applications ● Uninterruptible Power Supplies (UPS) ● Power supplies for welding applications ● Single or three phase inverters ● Auxiliary converters ● Substations. 97.R4.60.000.0 19April2021/Version 2 LEM reserves the right to carry out modifications on its transducers, in order to improve them, without prior notice Page 1/13 LEM International SA Chemin des Aulx 8 1228 PLAN-LES-OUATES Switzerland www.lem.com DVC 1000-UI Safety ⚠ Caution If the device is used in a way that is not specified by the manufacturer, the protection provided by the device may be compromised. Always inspect the electronics unit and connecting before using this product and do not use it if damaged. Mounting assembly shall guarantee the maximum primary conductor temperature, fulfill clearance and creepage distance, minimize electric and magnetic coupling, and unless otherwise specified can be mounted in any orientation. Caution, risk of electrical shock This transducer must be used in limited-energy secondary circuits SELV according to IEC 61010-1, in electric/electronic equipment with respect to applicable standards and safety requirements in accordance with the manufacturer’s operating specifications. Use caution during installation and use of this product; certain parts of the module can carry hazardous voltages (e.g. power supply, primary conductor). Ignoring this warning can lead to injury and or/or cause serious damage. All installations, maintenance, servicing operations and use must be carried out by trained and qualified personnel practicing applicable safety precautions. This transducer is a build-in device, whose hazardous live parts must be inaccessible after installation. This transducer must be mounted in a suitable end-enclosure. Besides make sure to have a distance of minimum 30mm between the primary terminals of the transducer and other neighboring components. Main supply must be able to be disconnected. Never connect or disconnect the external power supply while the primary circuit is connected to live parts. Never connect the ouptut to any equimement with a common mode voltage to earth greater than 30V. Always wear protective clothing and gloves if hazardous live parts are present in the installation where the measurement is carried out. This transducer is a built-in device, not intended to be cleaned with any product. Nevertheless if the user must implement cleaning or washing process, validation of the cleaning program has to be done by himself. ESD susceptibility The product is susceptible to be damaged from an ESD event and the personnel should be grounded when handling it. Do not dispose of this product as unsorted municipal waste. Contact a qualified recycler for disposal. Underwriters Laboratory Inc. recognized component. 19April2021/Version 2 LEM reserves the right to carry out modifications on its transducers, in order to improve them, without prior notice Page 2/13 LEM International SA Chemin des Aulx 8 1228 PLAN-LES-OUATES Switzerland www.lem.com DVC 1000-UI Absolute maximum ratings Parameter Symbol Unit Value Maximum DC supply voltage ⎓ (UP = 0 V, 0.1 s) ÛC max V 28 Maximum DC supply voltage ⎓ (working) (− 40 … + 85 °C) UC max V 25.2 Electrostatic discharge voltage (HBM - Human Body Model) UESD HBM kV 4 UHV+ + UHV− and |UHV+ − UHV−| kV ≤ 1.5 Maximum DC common mode voltage Absolute maximum ratings apply at 25 °C unless otherwise noted. Stresses above these ratings may cause permanent damage. Exposure to absolute maximum ratings for extended periods may degrade reliability. Environmental and mechanical characteristics Parameter Ambient operating temperature Ambient storage temperature Symbol Unit Min TA °C −40 85 TA st °C −50 90 Typ Max Comment Equipment operating temperature class EN 50155: OT6 Switch-on extended operating temperature class EN 50155: ST0 Rapid temperature variation class EN 50155: H2 Conformal coating type EN 50155: PC2 RH Relative humidity % 95 Shock & vibration categorie and class EN 50155: 1B, (EN 61373) m Mass g 57 Ingress protection rating IP20 Altitude m IEC 60529 (Indoor use) 2000 Pollution degree 1) PD3 2) Insulation voltage accordingly Note(s): Insulation coordination at 2000 m 1) 2) PD2 max accordingly to UL 508 RAMS data Parameter Symbol Unit Min Typ Max Comment Useful life class EN 50155: L4 Mean failure rate According to IEC 62380 TA = 45 °C ON: 20 hrs/day ON/OFF: 320 cycles/year UC = 15 ... 24 V, UP = 1000 V 19April2021/Version 2 λ h-1 1/1029866 LEM reserves the right to carry out modifications on its transducers, in order to improve them, without prior notice Page 3/13 LEM International SA Chemin des Aulx 8 1228 PLAN-LES-OUATES Switzerland www.lem.com DVC 1000-UI UL 508: Rating and assumptions of certification File # E189713 Volume: 2 Section: 16 Standards ● Canadian Standard for industrial Control Equipment CSA C22.2 No. 14-18 ● US Standard for Industrial Control Equipement UL 508 Conditions of acceptability When installed in the end-use equipment, consideration shall be given to the following: 1. Models DVC 1000-UI are intended to be mounted on a DIN rail or a mounting plate. 2. The terminals have not been evaluated for field wiring. 3. Low voltage control circuit shall be supplied by an isolating source (such as a transformer, optical isolator, limiting impedance or electro-mechanical relay). 4. These devices are intended to be mounted in an ultimate enclosure. 5. The products have been evaluated for a maximum surrounding air temperature of 85 °C. 6. These devices are intended to be installed in a pollution degree 2 max. Marking Only those products bearing the UL or UR Mark should be considered to be Listed or Recognized and covered under UL's Follow-Up Service. Always look for the Mark on the product. 19April2021/Version 2 LEM reserves the right to carry out modifications on its transducers, in order to improve them, without prior notice Page 4/13 LEM International SA Chemin des Aulx 8 1228 PLAN-LES-OUATES Switzerland www.lem.com DVC 1000-UI Insulation coordination Parameter Symbol Unit ≤ Value RMS voltage for AC insulation test at 50 Hz Ud kV 4.26 Type test: 1mn Routine test: 10s (100 % tested in prod.) Both tests according to IEC 62497-1 Impulse withstand voltage 1.2/50 μs UNi kV 7.84 According to IEC 62497-1 Partial discharge RMS test voltage (qm < 10 pC) Ut V 1650 According to 61800-5-1 - - Case material Comparative tracking index CTI V0 Comment According to UL 94 600 Between primary and secondary 1000 600 300 Maximum RMS insulation voltage 1) CAT I & II CAT III CAT IV Clearance dCI mm 9.0 Shortest distance through air Creepage distance dCp mm 9.0 Shortest path along device body Application example RMS voltage line-to-neutral V 600 Basic insulation according to IEC 61010-1, CAT III, PD2 Application example RMS voltage line-to-neutral V 300 Reinforced insulation according to IEC 61010-1, CAT III, PD2 Application example System voltage RMS V 600 Basic insulation according to IEC 61800-5-1, IEC 62109-1 CAT III, PD2 Application example System voltage RMS V 600 Reinforced insulation according to IEC 61800-5-1, IEC 62109-1 CAT III, PD2 Application example Rated insulation RMS voltage V 600 Basic insulation according to IEC 62497-1 CAT III, PD2 V 500 Reinforced insulation according to IEC 62497-1, CAT III, PD2 V 1000 Insulation according to UL 508, CAT II, PD2 Application example Rated insulation RMS voltage UNm Operating voltage Between primary and ground Clearance dCI mm 9.8 Shortest distance through air Creepage distance dCp mm 9.8 Shortest path along device body V 300 Reinforced insulation according to IEC 61010-1, CAT III, PD2 Application example Rated insulation RMS voltage Between secondary and ground Clearance dCI mm 8.7 Shortest distance through air Creepage distance dCp mm 8.7 Shortest path along device body V 300 Reinforced insulation according to IEC 61010-1, CAT III, PD2 Application example Rated insulation RMS voltage Note:1) Electronic board limitation 19April2021/Version 2 LEM reserves the right to carry out modifications on its transducers, in order to improve them, without prior notice Page 5/13 LEM International SA Chemin des Aulx 8 1228 PLAN-LES-OUATES Switzerland www.lem.com DVC 1000-UI Electrical data At TA = TA min ... TA max, UC = 20 V, RM= 100 Ω, unless otherwise noted (see Min, Max, typ, definition paragraph in page 7). Parameter Symbol Unit Min UP N DC V 0 RM Ω 0 IS N DC mA 4 Secondary current limit IS L mA 0.5 DC supply voltage ⎓ UC V 15 DC current consumption ⎓ IC mA Primary nominal DC voltage (continuous) Measuring resistance Secondary nominal direct current (continuous) Typ Max Comment 1000 see derating on figure 1 20 20 full primary voltage range 21 see figure 2 24 +5 % / -7 % on voltage range UC = 24 V, UC = 15 V, 22 21 UP = 0 V@ 25 °C UP = 0 V@ 25 °C Inrush current NA (EN 50155) Interruptions on power supply voltage class NA (EN 50155) Supply change-over class NA (EN 50155) Power consumption UP= 0 V @ UC PC W 0.53 @ 24 V Power consumption UP= UPN DC @ UC PC W 0.61 @ 24 V Rise time of UC (10 % ... 90 %) trise ms Total error εtot % -1.7 1.7 Total error εtot % -1 1 Temperature variation of UO referred to primary UO E T V -3.00 3.00 referred to 25 °C Electrical offset voltage referred to primary UO E V -6.00 6.00 @ 25 °C, 100 % tested in production Sensitivity S µA/V Sensitivity error εS % -1 1 Temperature variation of sensitivity error εS T % -0.4 0.4 referred to 25 °C εL % of UP N -0.2 0.2 @ 25 °C, 0-1000 V range RMS noise voltage 100 Hz … 100 kHz referred to primary Uno mV Delay time @ 10 % of the final output value UP N step tD 10 µs 5 Delay time @ 90 % of the final output value UP N step tD 90 µs 17 Frequency bandwidth (−3 dB) (−1 dB) BW kHz 35 19 Start-up time tstart ms 20 Resistance of primary circuit RP MΩ 12.6 Total primary power loss @ UP N PP W 0.08 Linearity error 19April2021/Version 2 100 @ 25 °C, 100 % tested in production 16 @ 25 °C 1000 LEM reserves the right to carry out modifications on its transducers, in order to improve them, without prior notice Page 6/13 LEM International SA Chemin des Aulx 8 1228 PLAN-LES-OUATES Switzerland www.lem.com DVC 1000-UI Definition of typical, minimum and maximum values Minimum and maximum values for specified limiting and safety conditions have to be understood as such as well as values shown in “typical” graphs. On the other hand, measured values are part of a statistical distribution that can be specified by an interval with upper and lower limits and a probability for measured values to lie within this interval. Unless otherwise stated (e.g. “100 % tested”), the LEM definition for such intervals designated with “min” and “max” is that the probability for values of samples to lie in this interval is 99.73 %. For a normal (Gaussian) distribution, this corresponds to an interval between −3 sigma and +3 sigma. If “typical” values are not obviously mean or average values, those values are defined to delimit intervals with a probability of 68.27 %, corresponding to an interval between −sigma and +sigma for a normal distribution. Typical, maximal and minimal values are determined during the initial characterization of the product. 19April2021/Version 2 LEM reserves the right to carry out modifications on its transducers, in order to improve them, without prior notice Page 7/13 LEM International SA Chemin des Aulx 8 1228 PLAN-LES-OUATES Switzerland www.lem.com DVC 1000-UI Typical performance characteristics 22 20 1000 18 Output current (mA) Maximum measuring resistance (Ohm) 1200 TA = -40 ... 85°C 800 600 400 200 0 16 14 12 10 8 6 4 2 0 200 400 600 800 0 1000 -500 -250 0 250 Measuring range (V) Figure 1: Maximum measuring resistance RM max = 20 Total error (%) 0.8 Electrical offset drift (µA) 25 Max 0.6 Typical 0.4 Min 0.2 0.0 -0.2 -0.4 15 10 5 0 -5 Max -10 Typical -15 Min -20 -25 0 25 50 75 -25 100 -50 -25 0 Ambient temperature 50 25 75 100 Ambient temperature Figure 3: Total error in temperature Figure 4: Electrical offset thermal drift 1.4 0.25 1.0 Max 0.8 Typical 0.6 Min Linearity error (% of Upn) 1.2 Sensitivity drift (%) 1000 Figure 2: Output secondary current 1.0 -50 750 1625000 Ω 4 x UP + 1000 1.2 -0.6 500 Input voltage (V) 0.4 0.2 0.2 0.15 0.1 0.05 0.0 -0.2 0 -50 -25 0 25 50 75 100 0 200 Figure 5: Sensitivity thermal drift 19April2021/Version 2 400 600 800 1000 Primary voltage (V) Ambient temperature (°C) Figure 6: Typical linearity error at 25 °C LEM reserves the right to carry out modifications on its transducers, in order to improve them, without prior notice Page 8/13 LEM International SA Chemin des Aulx 8 1228 PLAN-LES-OUATES Switzerland www.lem.com DVC 1000-UI Typical performance characteristics UP UP IS IS Input UP: 200 V/div Output IS: 5 mA/div Timebase: 0.5 µs/div Input UP: 200 V/div Output IS: 5 mA/div Timebase: 5 µs/div Figure 8: Typical step response (0 to 1000 V) Figure 7: Detail of typical common mode perturbation (1000 V step with 6 kV/µs, RM = 100 Ω) 1 0 0 -20 -40 Phase (deg) Gain (dB) -1 -2 -3 -60 -80 -100 -4 -120 -5 -140 -6 -160 0.01 0.10 1.00 Frequency (kHz) 10.00 100.00 Figure 9: Gain function of frequency (Up ≥ 0 V with AC signal superposed to a positive DC component) 0.01 0.10 1.00 Frequency (kHz) 10.00 100.00 Figure 10: Phase shift function of frequency (Up ≥ 0 V with AC signal superposed to a positive DC component) Typical supply current (mA) 25 20 15 15V 24V 10 5 0 -40 -20 0 20 40 60 80 100 Ambient temperature (°C) Figure 11: Supply current function of temperature 19April2021/Version 2 LEM reserves the right to carry out modifications on its transducers, in order to improve them, without prior notice Page 9/13 LEM International SA Chemin des Aulx 8 1228 PLAN-LES-OUATES Switzerland www.lem.com DVC 1000-UI Typical performance characteristics -100 1.E+01 -110 1.E+00 -120 1.E-01 -140 Uno (Vrms) Ino (dB Arms/Hz1/2) -130 -150 1.E-02 -160 1.E-03 -170 -180 1.E-04 -190 -200 1.E-05 0.01 0.10 1.00 10.00 100.00 0.01 0.10 Figure 12: Typical output noise voltage spectral density Ino referred to secondary with RM = 50 Ω 1.00 10.00 100.00 Frequency (kHz) Frequency (kHz) Figure 13: Typical total output RMS noise voltage Uno referred to primary with RM = 50 Ω To calculate the total output RMS noise in a frequency band f1 to f2, the formula is: Uno(f1 to f2) = Uno (f2)2 − Uno (f1)2 with Uno(f) read from figure 13 (typical, RMS value). Example: What is the total output RMS noise from 100 to 1 kHz? Figure 13 gives Uno(100 Hz) = 8 mV and Uno(1 kHz) = 25 mV. Therefore, the total output RMS noise voltage referred to primary is 24 mV. 19April2021/Version 2 LEM reserves the right to carry out modifications on its transducers, in order to improve them, without prior notice Page 10/13 LEM International SA Chemin des Aulx 8 1228 PLAN-LES-OUATES Switzerland www.lem.com DVC 1000-UI Terms and definitions Electrical offset referred to primary UP UP max : primary voltage (V) : maximum primary voltage applied to the transducer (V) IS : secondary current (A) S : sensitivity of the transducer TCS : temperature coefficient of S TA : ambient operating temperature (°C) UO E : electrical offset voltage (V) UO T : temperature variation of UO E (V) εS : sensitivity error at 25 °C εS T : thermal drift of S εL(UP max) : linearity error for UP max This model is valid for primary voltage UP between 0 and +UP only. This is the absolute maximum error. As all errors are independent, a more realistic way to calculate the error would be to use the following formula: ε= N ∑ ε i2 The total error εtot is the error at ±UP N, relative to the rated value UP N. It includes all errors mentioned above ● the electrical offset UO E ● the sensitivity error εS ● the linearity error εL (to UP N). Total error ℇ tot at UC = ... V and TA = 25 °C 1 2 3 4 5 Step KO L: Overload factor Figure 15: v oltage cycle used to measure the electrical offset (transducer supplied) Using the voltage cycle shown in previous figure, the electrical offset voltage UO E is the residual output referred to primary when the input voltage is zero. The temperature variation UO T of the electrical offset voltage UO E = U P (3) + U P (5) 2 U O T (T ) = U O E (T ) − U O E ( 25 °C ) To measure sensitivity and linearity, the primary voltage (DC) is cycled from 0 to UP, then to −UP and back to 0 (equally spaced UP/10 steps). The sensitivity S is defined as the slope of the linear regression line for a cycle between ±UP N. The linearity error εL is the maximum positive or negative difference between the measured points and the linear regression line, expressed in % of UP N. Delay times aver. + 3σ The delay time tD 10 @ 10 % and the delay time tD 90 @ 90 % with respect to the primary are shown in the next figure. Both slightly depend on the primary voltage dv/dt. They are measured at nominal voltage. 0,10 0,08 ℇ tot (% UP N) -1 Sensitivity and linearity Total error referred to primary 0,06 U 0,04 UO E (max) / UP N 0,02 100 % 90 % 0,00 -0,02 0 UO E is the variation of the electrical offset from 25 °C to the considered temperature. i =1 0,12 Primary voltage cycle 1 with KOL = 1 .. 10 The static model of the transducer with current output at temperature TA is: IS = S ⋅ UP ⋅ (1 + ε) In which (referred to primary): ε ⋅ UP = UO E + UO T + εS ⋅ UP + εS T ⋅ UP + εL(UP max) ⋅ UP max UP / (KOL · UP N) Simplified transducer model US UP -1 -0,5 0 0,5 UP / (KOL · UP N) with KOL = 1 .. 10 Figure 14: Total error εtot tD 90 1 10 % tD 10 t Figure 16: delay time tD 10 @ 10 % and delay time tD 90 @ 90 %. 19April2021/Version 2 LEM reserves the right to carry out modifications on its transducers, in order to improve them, without prior notice Page 11/13 LEM International SA Chemin des Aulx 8 1228 PLAN-LES-OUATES Switzerland www.lem.com DVC 1000-UI Rail DIN mounting 1. Place DVC on DIN rail adaptor support respecting the 2 Poka-Yoke features 2. Tighten the 2 PT screws from the adaptor kit (torque = 0.4 N.m ±20 %) 3. Place DIN rail lower edge inside DIN rail adaptor support lower notch 4. Help the blue spring lock to move up with a flat screwdriver 5. Then rotate transducer to place it on the rail 6. When placed, relax the force applied with screwdriver. 7. Manually test that transducer is well fixed Rail DIN kit referemence number 93.30.R2.000.0 to be ordered separately. 19April2021/Version 2 LEM reserves the right to carry out modifications on its transducers, in order to improve them, without prior notice Page 12/13 LEM International SA Chemin des Aulx 8 1228 PLAN-LES-OUATES Switzerland www.lem.com DVC 1000-UI Dimensions (in mm) Connection Insulation barrier Critical distances between Primary, Secondary and Ground are internal to embedded electronics (see page 4) Mechanical characteristics Remarks ● General tolerance ● Transducer fastening Recommended fastening torque ● Primary and secondary connections - use a flat head screwdriver with ⌀ 2.5 mm (recommended) - slowly press the connector through the cover dedicated holes until the wire is locked/unlocked ±0.5 mm 2 holes ⌀ 4.4 mm 2 M4 steel screws 2.1 N.m (±10 %) WAGO 2061 connectors 20 ... 16 AWG (solid or fine-stranded conductor) with strip length between 7 to 10 mm ● IS is positive when UHV+ − UHV− > 0 V ● The primary cables have to be routed together all the way (< 30 m) ● The secondary cables also have to be routed together all the way ● Installation of the transducer must be done unless otherwise specified on the datasheet, according to LEM Transducer Generic Mounting Rules. Please refer to LEM document N°ANE120504 available on our Web site: https://www.lem.com/en/file/3137/download/ Note: Additional information available on request. 19April2021/Version 2 LEM reserves the right to carry out modifications on its transducers, in order to improve them, without prior notice Page 13/13 LEM International SA Chemin des Aulx 8 1228 PLAN-LES-OUATES Switzerland www.lem.com